Alien Slope Soarer & DLG 1.2m - RC Models (2025)

Kit arrived with parts missing . No servo covers or wing fixings . One of the expensive servos does not centre correctly.. the holes in the wing did not line up with the fuselage so a bit of messing around with that. Have not flown it yet as I need to buy another servo 😔. Not my best experience so far .

Well, a follow up to my previous review. I've never had a premium moulded glider before wirh so many issues. The wing is made of two layers of carbon cloth laid at 90 degrees to each other - halfway along one wing half, the top carbon layer was split apart, leaving a 1/4in line across the wing with only one layer of cloth. A worrying strength issue. A detailed check of the bag of bits - a wing fixing bolt was missing and the two elevon push rod wires were different lengths, one just too short. Lesson - do not rely on the wire measurements in the instructions as they were certainly wrong for my kit. Having bent one pushrod to the stated dimensions, it didn't fit, so I had to re-make it using my own wire. The other piece of wire was too short, so I also had to replace that. So overall, not a great kit of parts + instructions for something costing this much. I only hope it flies OK once the rain stops.

Arrived quickly and undamaged (nice packing Hyperflight!). On inspection, a small section of the carbon cloth weave on the wing upper surface was misaligned, which was a shame as it rather draws the eye even if the build strength doesn't seem affected. Overall, however, a nice kit of parts, and as soon as the delayed rudder servo arrives I'll get building. Can't wait!

Again short waiting for the pakkingen, thanks Neil. Piece of art and crafts , well designet. Good manual too. Well along my way to bilder this plane ......but arter glueing in the ballasttube I tried to put in a 100gr weigt white holding the rudderservo with mount several times , no way. Do I misunderstand the way of loading ? PS I fond 21 krone-coins and a regularitet 3mm bolt to put trough and voila a perfekt 100gr load ready for use ( and easy to adjust for preferance) So welcome to Norway to get these coins :):)
I build my rudder movement by pushrod ( Carbon 1mm of course ) by the way, after som flutter trouble in other light models in speedy movements.
So nice to read all the warnings for accurate building ....... it gratifies the gratifies the quality of this plane I think. Looking forward to my first flights , Fred

Again short waiting for the pakkingen, thanks Neil. Piece of art and crafts , well designet. Good manual too. Well along my way to bilder this plane ......but arter glueing in the ballasttube I tried to put in a 100gr weigt white holding the rudderservo with mount several times , no way. Do I misunderstand the way of loading ? PS I fond 21 krone-coins and a regularitet 3mm bolt to put trough and voila a perfekt 100gr load ready for use ( and easy to adjust for preferance) So welcome to Norway to get these coins :):)
I build my rudder movement by pushrod ( Carbon 1mm of course ) by the way, after som flutter trouble in other light models in speedy movements.
So nice to read all the warnings for accurate building ....... it gratifies the gratifies the quality of this plane I think. Looking forward to my first flights , Fred

Really happy with the quality of the model and how it went together. After about 5 hours I was out throwing it around and having a ball.
And as always great service from Hyperflight

We have a couple Aliens now!!!....My girlfriend is gonna commandeer the pink one and I'll take over this new orange job.....Too much fun with these things!!!....Got here (Orange County, CA) in 5 days!!!

Thanks �gain to Neil for keeping this great hobby supplied with so many quality items, Alien arrived in 24 hrs after purchase well boxed, Build instruction very clear, Accuracy is key to this Model . Have built with recommended servos and lipo. Time taken around 5 hrs total, Alien fly's very well no nasty surprise. 2mm up trim on elevons for normal flight zero for speed or when conditions suit , flown in 5 knot and 12 knot winds aerobatic and good speed thermalization really love this model worth every penny , many thanks to are Ukraine Friend's

...absolute perfect and superfast service by Neil !!!
I'd never thought a purchase in GB..and shipping to the EU could be that easy..

this is my first carbon build and its very simple. the instructions are clear and the 3D printed parts fit perfectly. It's a well thought out machine and I drilled a bore in a copper cylinder to fit in the ballast tube for 30g and 50g slugs. As a left handed flyer, the fin hinge is on the left hand side so that's something to be aware of if you're wanting it for a left hand launch dlg. as usual impeccable service from Neil.

As a kit designer and manufacturer I was really excited to see the Alien appear on Hyperflight, and it was a must have toy. Its not often I take the plunge on a model I didn't design myself and really happy I did. Whilst the build hasnt started yet due to other commitments the quality of the components and the fit and finish is exceptional and more that meets my own expectations. I fully intend to do a mini review of the model when I start construction and will share my findings with Neil.